Use df robot sensor instead

lilygo-sensor-clock.ino

@@ -9,6 +9,11 @@
 #include <XPowersLib.h>
 #include <HTTPClient.h>
 #include "freertos/semphr.h"
+#include "DFRobot_mmWave_Radar.h"
+#include <HardwareSerial.h>
+
+#include "Thread.h"
+#include "ThreadController.h"
 
 // Serial
 #define BAUD 115200
@@ -18,25 +23,20 @@
 #define TX2_PIN TOUCH_IICSDA
 
 // Sensor configuration
-#define COMMAND "FDFCFBFA0800120000000200000004030203" //Normal mode command, see documentation waveshare sensor
+#define PRESENCE_DISTANCE 2 // in m
-#define PRESENCE_DISTANCE 200 // in cm
 #define DELAY_STATUS_CHECK 1000 // delay (in ms) between two checks of the presence
 #define SLEEP_DELAY 30000 // delay (in ms) until sleep mode
 #define POWER_DELAY 100000 // delay (in ms) until turning off the screen
 
-byte configCommand[] = {
+HardwareSerial mySerial(1);
-  0xFD, 0xFC, 0xFB, 0xFA, 0x08, 0x00, 0x12, 0x00,
+DFRobot_mmWave_Radar sensor(&mySerial);
-  0x00, 0x00, 0x02, 0x00, 0x00, 0x00, 0x04, 0x03,
-  0x02, 0x03
-};
 
 SemaphoreHandle_t xSemaphore = NULL;
 PowersSY6970      PMU;
 
 // Sensor variables
 uint16_t state = 1; // 0 = presence detected, 1 = no presence detected for the past SLEEP_DELAY ms, 2 = no presence detected for the past POWER_DELAY ms
-unsigned long lastMotionCheckTime = millis();
+unsigned long lastMotionDetected = 0; // time when the last motion was detected
-unsigned long lastMotionDetected = 0;
 
 // Time variables
 static uint32_t last_tick;
@@ -52,6 +52,10 @@ static lv_color_t        *buf1;
 static String BASE_URL_HA = "http://192.168.1.2:8123/api/services";
 static String HA_TOKEN = "abc";
 
+ThreadController controller;
+Thread thread1 = Thread();
+Thread thread2 = Thread();
+
 void setup() {
     xSemaphore = xSemaphoreCreateBinary();
     xSemaphoreGive(xSemaphore);
@@ -60,10 +64,12 @@ void setup() {
     initializeWifi();
     initializeTime();
     initializeUI();
+    initializeThreading();
 }
 
 void loop() {
-    delay(1);
+    controller.run();
+
     if (transfer_num <= 0 && lcd_PushColors_len <= 0)
         lv_timer_handler();
 
@@ -74,9 +80,6 @@ void loop() {
     static int           flag_bl = 0;
     static unsigned long cnt     = 0;
 
-    printLocalTime();
-    readAndProcessSensorLines();
-
     cnt++;
     if (cnt >= 100) {
         if (flag_bl == 0) {
@@ -110,12 +113,12 @@ void initSerial() {
     digitalWrite(TOUCH_RES, HIGH);
     delay(2);
 
-    // Start Serial2 for the HMMD Sensor
+    // Start HMMD Sensor
-    Serial2.begin(BAUD, SERIAL_8N1, RX2_PIN, TX2_PIN);
+    mySerial.begin(BAUD, SERIAL_8N1, RX2_PIN, TX2_PIN);  //RX,TX
-    Serial.println("Serial2 Initialized on RX:" + String(RX2_PIN) + ", TX:" + String(TX2_PIN));
+    Serial.println("Sensor Initialized on RX:" + String(RX2_PIN) + ", TX:" + String(TX2_PIN));
-    Serial.println("Sending configuration to the sensor");
+    sensor.factoryReset();    //Restore to the factory settings 
-    delay(2000);
+    sensor.DetRangeCfg(0, PRESENCE_DISTANCE);    //The detection range is as far as 9m
-    Serial2.write(configCommand, sizeof(configCommand));
+    sensor.OutputLatency(0, 0);
 }
 
 void initializeWifi() {
@@ -188,6 +191,17 @@ void initializeUI() {
     Serial.println("UI initialized");
 }
 
+void initializeThreading() {
+    thread1.onRun(printLocalTime);
+    thread1.setInterval(100);
+
+    thread2.onRun(readAndProcessSensorLines);
+    thread2.setInterval(1000);
+
+    controller.add(&thread1);
+    controller.add(&thread2);
+}
+
 void printLocalTime() {
     if (millis() - last_tick > 100) {
         struct tm timeInfo;
@@ -203,51 +217,31 @@ void printLocalTime() {
 }
 
 void readAndProcessSensorLines() {
-    if (millis() - lastMotionCheckTime >= DELAY_STATUS_CHECK) {
+    int currentStatus = sensor.readPresenceDetection();
-        lastMotionCheckTime = millis();
-        // Check if data is available on Serial2
-        while (Serial2.available() > 0) {
-            // Read a line of text until a newline character (\n) is received
-            // The timeout helps prevent blocking forever if a line ending is missed
-            String line = Serial2.readStringUntil('\n');
 
-            // Clean up the line: remove potential carriage return (\r) and leading/trailing whitespace
+    if (currentStatus == 1) {
-            line.trim();
-        
-            // Check if the line contains the "Range" information
-            if (line.startsWith("Range ")) {
-                // Extract the substring after "Range "
-                String distanceStr = line.substring(6);
-                int distance = distanceStr.toInt();
-                bool currentStatus = distance <= PRESENCE_DISTANCE;
-
-                if (currentStatus) {
         lastMotionDetected = millis();
     }
 
-                //Serial.print("Radar: ");
+    //Serial.printf("Sensor: %d\n", currentStatus);
-                //Serial.println(distance);
 
-                if (currentStatus && state != 0) {
+    if (currentStatus == 1 && state != 0) {
         state = 0;
         Serial.println("Motion detected, turning screen on.");
         lv_msg_send(MSG_NEW_VOLT, "0");
         //restApiAction(0);
-                } else if (!currentStatus && state == 1 && (millis() - lastMotionDetected >= POWER_DELAY)) {
+    } else if (currentStatus == 0 && state == 1 && (millis() - lastMotionDetected >= POWER_DELAY)) {
         state = 2;
         Serial.printf("No motion detected for %d ms, turning screen off.\n", POWER_DELAY);
         lv_msg_send(MSG_NEW_VOLT, "2");
         //restApiAction(2);
-                } else if (!currentStatus && state == 0 && (millis() - lastMotionDetected >= SLEEP_DELAY)) {
+    } else if (currentStatus == 0 && state == 0 && (millis() - lastMotionDetected >= SLEEP_DELAY)) {
         state = 1;
         Serial.printf("No motion detected for %d ms, turning screen screensaver on.\n", SLEEP_DELAY);
         lv_msg_send(MSG_NEW_VOLT, "1");
         //restApiAction(1);
     }
 }
-        }
-    }
-}
 
 // action: 0 => Screen on, => 1 Screen off, => 2 Power off
 void restApiAction(int action) {